P0016 Ford F150 – Causes, Repairs, and Costs

Posted on

Ford F150 Code P0016 – Causes, Repairs, and Costs catdumptruck.com | Are you experiencing the symptoms of code P0016? If so, you might be looking for a solution to fix this problem.

Here are some possible causes, repairs, and costs for this problem. Hopefully, the information in this article will help you determine what the issue is and how to fix it.

You may also want to invest in a scan tool. However, you should not attempt to fix this problem on your own. Rather, take your vehicle to a mechanic for a proper diagnosis.

P0016 Ford F150


Having a problem with your Ford F150’s P0016 engine code is a sign that there is a problem with your timing chain. It may not have been properly aligned when installed, or it may have jumped a few teeth.

If this is the case, you need to take the vehicle to a mechanic to have the chain re-aligned. Many manufacturers have strict service intervals for timing chains.

This is because even a slight misalignment can cause the code to appear. In addition, the crankshaft sensor uses a ring or notches to determine where the crank is positioned, so if the timing chain is out of alignment, the sensor will not be able to get an exact reading.

The main symptom of P0016 is a hard start or no-start scenario. If the motor will not start, the check engine light will illuminate, and the engine will exhibit rough idling.

This code may also result in the engine stalling. When this happens, the tone ring will be damaged, causing the engine to run rough or not at all. The cost of fixing the problem will depend on what type of failure is causing the code.

The cause of a P0016 engine code is difficult to pinpoint. Several factors can lead to this code, including a bad sensor, a stretched timing belt, or dirty oil.

It is a good idea to have a professional mechanic take a look at the vehicle to determine what might be the source of the code. Once you know the cause of the code, you can begin to solve the problem.

Some of the most common causes of P0016 are dirty oil, stretched timing belt, or damaged timing chain. If these are not the culprits, you can check the crankshaft sensor by using a vacuum gauge.

Having a dirty engine can result in poor gas mileage and lack of power. The right mechanic can identify the problem and fix the problem for you. If you don’t want to spend a fortune on a diagnostic, take the vehicle to a repair shop.


Having the “P0016” code on your Ford F150? It means that the Crankshaft Position Sensor (CPM) and Camshaft Position Sensor (CAM) are not in sync with each other.

This can be a problem with the wiring or the sensor itself. A good way to check if the problem is the timing belt or a faulty solenoid is to take your car to a mechanic.

This trouble code can be caused by a variety of issues, ranging from the smallest problem to a severe one. There are several causes and symptoms of P0016 Ford F150 problems, and finding one that is right for you can be difficult.

The cost of repair depends on the type of failure and the time needed to diagnose it. However, it will cost you anywhere from $75 to $150, depending on the shop.

Among the most common causes of P0016, the problem with the timing chain and camshaft position sensors can be the culprit.

If the timing chain or camshaft is off-kilter, the engine will not run correctly. If the camshaft and timing belt are not working, the P0016 code could mean that you need to replace the entire system.

Fortunately, many people do not have to spend a lot of money on auto repair services, but a little bit of knowledge can go a long way.

Other common causes of P0016 Ford F150 code include faulty oil control valves. These parts are the culprit behind poor gas mileage and lack of power at high RPM.

If they are failing, your F150’s computer will display P0016 in its code list. A new oil control valve is another reason for P0016 to appear on your Ford F150. When this happens, your F150 may not start at all, so you should replace it immediately.

P0016 Ford F150


The first step in repairing the P0016 error code is to replace the timing chain. Replacing the chain is a relatively simple job that does not require any special mechanic knowledge.

Another problem that can cause this code is the camshaft/crankshaft position sensor. The sensors send inaccurate data, which can cause mismatched fuel delivery and ignition timing. Luckily, you don’t need to be a master mechanic to replace the position sensor.

You can also use a scan tool to check for the P0016 code. For more advanced diagnostics, you can use a tool like FIXD to perform a code check. In addition, you should check for any technical service bulletins.

Technical Service Bulletins (TSBs) are written specifically for your vehicle and can prevent this fault. By following the instructions found in these documents, you can find and repair the P0016 code in your vehicle.

To do a diagnosis on the F150, you can use a scan tool or an OBDII scanner. If you have an OBDII scanner, you can manually clear the P0016 code.

To be sure you have removed the error, you can run another scan with the scan tool to confirm the removal of the error code. However, if you’d rather hire a mechanic, you should be prepared to spend a fair amount of money on diagnostics.

If you notice that your gas mileage has decreased significantly, your timing chain is probably the culprit. It can also be caused by a compromised engine timing part.

Checking for a timing chain failure can save you time and money, and you’ll avoid costly mistakes by replacing the wrong parts. Moreover, if your timing chain fails, it could result in a severe engine malfunction, especially if the valves hit the pistons.

You can also inspect the cylinder head for leaks and plugged fuel lines. A good indicator that your reluctor ring needs repair is a rattle. Lastly, check the valve for oil leaks and if they are loose.

Replace the cylinder head as well as the valve, if you have one. Then, your Ford F150 is ready for service! It won’t let you down again!


If your Ford F150 is suffering from a P0016 code, you might be wondering how much it will cost to fix it yourself. The actual cost of a repair will depend on the type of car, make, and year, as well as the mechanic’s labor rates.

A timing belt repair, for example, can cost $500 to $1,000, while a camshaft variable timing solenoid repair can cost $300 to $400.

The most common problem with the Ford F150’s 3.5L Ecoboost engine is a problematic timing chain. This problem affects only the 1st generation 3.5L EcoBoost engines from 2011 to 2015.

Other symptoms include rattling noises during cold starts, a faulty check engine light, and diagnostic trouble code P0016.

While timing chains are the most common culprit, the problem has been reported in other components, including the tensioner, chain guides, and cam phasers.

The first step in repairing a P0016 on a Ford F150 is to check the wiring harness. This component is susceptible to damage from hot exhaust and vibration.

To ensure the correct position of the sensor, you can inspect it at a mechanic’s shop. If it is out of alignment, the timing chain may need to be replaced. If the wiring harness is not properly aligned, the P0016 code will appear.

The next step is to determine what caused the code. The P0016 code means that the intake camshaft position sensor is faulty. If the camshaft doesn’t turn freely, the problem is likely to damage the engine and its components.

The resulting symptoms can include a hard start, rough running, and no power at WOT. Fortunately, repairPal can help you find a trusted mechanic in your area. RepairPal will provide upfront quotes and guarantee reasonable prices for repairs.

Divka Kamilah
Latest posts by Divka Kamilah (see all)
Gravatar Image
Divka really likes writing, reading, camping, cooking and being a productive housewife and being the best teacher for her children is her dream.

Leave a Reply

Your email address will not be published. Required fields are marked *